D-ILA™ PROJECTOR80VERSION 1.0OWNER’S OPERATING MANUAL
10Controls and Features$PWFS-BUDIFTProjector Chassis CoverTo Open the Projector Cover:1. Locate the two black cover latches under the front edge.2.
11Connector PanelRS-232C DVISVCSYNCOUT1. [SYNC OUT] TerminalThis terminal is intended for servicing purposes. Do not use it. Using it may cause an er
12Controls and Features (continued)1. LAMP INDICATOR: Light On: Indicates the lamp has been used for more than 1900 hours. Blinking: Indicates tha
13*About Cool Down ModeAfter projection, the heated lamp will go through a 90-second cool-down process known as the cool down mode. This function is t
14TESTPRESETENTMUTELIGHT1. [ON] Button When this unit is in the standby mode, pressing the button for more than 1 second will turn this unit on and
15Installation EnvironmentThis unit is a precision device. Do not install it at the following places. Doing so may cause fi re or malfunction of the un
16Projector and Screen InstallationThe optimum image can be obtained when the center of the lens and the screen are placed perpendicular to each other
17"#"#4DSFFOScreen Size and Projection Distance • This unit uses a 1.3x manual zoom lens for projection.• Although the focusab
18Eff ective Range of Remote Control UnitThe operable distance of the remote control unit is about 23 ft. (7 m) for direct reception. The remote contro
19Connecting to DevicesBefore connection, be sure to turn off both the projector and the device to be connected. Connecting to the VDP-80 digital vid
2Introduction ... 3Contents of the package ...
20Connecting the Power Cord (supplied)After all devices have been connected, connect the supplied power cord.1 Connect the supplied power cord to the
21Basic Operation1 Turning on the power 1 Insert the power plug to the power outlet. • The main power turns on and the [STAND BY] indicator on
225 Turning on the power 1 Press the [POWER] button on this unit (or the [OFF] button on the remote control) for 1 or more seconds. • The [POWE
23Adjustments and Settings Using Menus8)*5&#"-(".."1*$563&"%+130+&$503015015*0/4*/'03."5*0/, $645
24Menu Operation ButtonsENTERButtonMain unit Remote controlFunctionMENUMENUEXITENTEREXITMain unitRemote control unitENTDisplays the main menu.
25Procedures for Menu Operation1 Press the [MENU] button• The main menu is displayed on the screen.Display of the menu item currently selected becomes
261 “Picture adjust” MenuTo adjust images.On the “Picture Adj.” menu, you can adjust the following items.“Gamma”Switches the gradation characteristics
27Screen Blanking1 Project image onto the screenImage for which the outer area has deteriorated2 Press the [MENU] button • The main menu is displayed
28V Shift Setting1 Project image onto the screen2.35:1 Cinemascope image 2 Press the [MENU] button • The main menu is displayed on the screen.8)*5&am
29Replacing the Lamp (For service personnel only)Lamp and Lamp Usage TimeThe maximum life of the lamp used for this unit is about 2000 hours, and may
3Thank you for purchasing the Vidikron Vision Model 80 projector and welcome to the Vidikron family. With proper setup and use, this prod-uct will bri
30Cleaning and Replacing the FilterHave your Vidikron dealer clean the fi lter regularly or air intake effi ciency may deteriorate and malfunction may o
31What to do when these messages are displayed Message Cause (Details)No device is connected to the DVI terminal.The terminal is connected but there
32Warning IndicationAbout warning indicatorsIf an abnormality occurs in this unit during projection, the warning mode will be triggered and the type o
33TroubleshootingBefore sending the unit to your Vidikron dealer for repair, check the following points.Symptom Probable Cause Corrective Action Refer
34Terminal DescriptionPin ArrangementPin No. Signal Name Pin No. Signal Name1 N/C 6 N/C2 RD 7 N/C3 TD 8 N/C4 N/C 9 N/C5 GNDPin No. Signal Name Pin No.
35RS-232C External ControlControl of this unit via an automation control system is possible by connecting it to this unit with a RS-232C cross cable (
36 2-3. Parameters used for the data format The following 3 types of parameters are used for command and response data: 1 Numeric value 2 ON/OF
37Specifi cationsProjection Type: D-ILA, 3-chip, 0.82 in. diagonalNative Resolution: 1920 x 1080 (16:9)Aspect Ratio: 4:3, Letterbox,16:9 AnamorphicDT
38Dimensions17.99820.1255.9324.4993.209
4Safety PrecautionsNOTICE (For USA)Language for Manuals of Products using HID Lamps (that contains mer-cury)This product has a High Intensity Discharg
Vidikron2900 Faber StreetUnion City, CA 94587510-324-5900Fax 510-324-59051-888-4-VIDIKRONRUMA-011080Version 1.0
5– Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating.The
6Safety Precautions (continued)WARNING:Do not cut off the main plug from this equipment. If the plug fi tted is not suitable for the power points in yo
7About Burning-in of D-ILA Device• Do not allow the same still picture to be projected for a long time or an abnormally bright video image to be proj
8Congratulations on your purchase of a Vidikron video product and welcome to the Vidikron family! With proper installation, setup and care, you should
9 EFFECTIVE WARRANTY DATE:This Limited Warranty begins on the eff ective date of delivery to the end user. For your convenience, keep the original bill
Commentaires sur ces manuels